「ZIFソケット」に関連した動画の一覧 |
 | Soldering extra headers and a ZIF socket in the AVR Dragon This is the video of my first time using lead-free solder! Sn 99.25% ,Cu 0.75%. I was soldering the extra male headers and a 3M ZIF socket in my brand new AVR Dragon :) 2010年08月04日再生回数 1902 |
 | Install a CPU central proccessing unit hardware how to This video gives the basic idea of installing an Sempron 2800+ 754 PGA (pin grid array)into the ZIF (zero insertion force) socket on a motherboard. The idea is the same for most PGA installations just match the pin grid to the alignment on the ZIF socket letting the cpu just drop into place then securing the ZIF socket leaver to ensure the cpu is securely installed. For the sake of annoyance, there is no sound. www.structuremonkey.com 2007年10月13日再生回数 3738 |
 | SNES EPROM cartridge Reprogrammable EPROM cartridge for the Super Nintendo. If the nerd voice is wacky, it's partially because I am still recovering from a flu. The rest is because I really do have a nerd voice. Mask ROM chip was removed, and pinout slightly re-wired for compatibility with 27C080 8-Mbit EPROM chips. The 32-pin ZIF socket makes changing EPROMs easy. While you can buy cheap EA Sports games as donor cartridges for $2 or $3, each ZIF socket cost me around $8 and each EPROM cost at least $4 or so, not to mention the EPROM programmer which is around $40 (and a UV tube for erasing the EPROMs). But hey, who would have thought that EA Sports games would be useful for something? It is possible to use donor carts with multiple mask ROMs as well as SRAM so you can even play RPGs and other games that have save data, but you have to pay attention to whether the donor cart and the game you want to play are LoROM or HiROM and other stuff I don't fully understand yet. Hacking information found at ROM Laboratory: nintendoallstars.w.interia.pl 2009年04月03日再生回数 16816 |
 | PS3 BD drive ribbon cable issue (plz help) I sent in three PlayStation 3 game consoles to be repaired (full reball with leaded solder; not a reflow that I could've done myself) and they came back like this... ready to be reassembled. That should've been pretty easy, but I seem to have hit a snafu with the simplest of things... reconnecting a ribbon cable to a low-profile ZIF socket. WTF?! 2011年03月02日再生回数 3729 |
 | Nixie IN 12 and KM155ID1 K155ID1 74141 tester Tester for in12 nixie tubes and k155id1 / 74141 nixie drivers. These chips are old, and they can easily be dead, so it's smart thing to test them before you leave positive feedback on ebay for it ;). This device lets you easily check just acquired nixie tubes and drivers. There is binary input with micro tactile buttons and display is on single nixie in-12 tube. IC is easily changeable through ZIF socket. 2011年09月25日再生回数 289 |
 | 3-in-1 Mini Lab by Au Group Electronics 3-in-1 mini-lab includs 28-pin SOIC ZIF socket and 40-pin DIP ZIF socket for programming, debugging, and other circuits for lab test: pull-up,pull down,VddCore capacitor, 6x LEDs etc. This video has a PIC16F628A SOIC chip in the SOIC ZIF socket. 2008年12月15日再生回数 813 |
 | AVR Programming - AVR Dragon Introduction This tutorial introduces the AVR Dragon. It is a device that allows us to program and debug AVR ATmega Microcontrollers. I show how to setup and use the AVR Dragon, soldering a 40 pin ZIF socket to the board and show how to connect it to AVR Studio 5 beta 2. I write a sample application and program it on an ATmega328. 2011年06月09日再生回数 12152 |
 | homemade jdm pic programmer homemade jdm serial port pic programmer with zif socket and pic16f628a 2012年04月05日再生回数 137 |
 | xtwin led mod this is a microcontroller driven led mod with low voltage alarm, for silverlit xtwin (super light rc airplanes). It is a work in progress. The item shown is crude lab prototype on a breadboard. probably only interesting to those who knows what it is. The zif-socket to the left contains a voltage regulator to drive the circuit. The zif-socket to the right contains a microcontroller, programmed to blink a white, red and green led in a certain pattern. The microcontroller also monitors the battery voltage and changes the blinking pattern if the voltage drops below a certain threshold. This way the pilot can be alerted in time and land safely before the battery dies. The state of this project is now almost ready, but I have little time for it right now. The current version on my desk is a 10x15mm double sided pcb with all surface mount electronics. Here is a picture of it; static.pici.se 2007年02月21日再生回数 5976 |
 | Remove and Install a PGA Processor-Part 1 of 2 In this video I describe and demonstrate how to remove a Pin Grid Array (PGA) processor from a Zero Insertion Force (ZIF) socket. Do you need IT certification training? Visit our website for more information @ www.techskills.edu. 2008年01月31日再生回数 8256 |
